Reinvent the tube
The Eisbecher Series consist of 20 different reservoirs that differ between usage, measurement and appearance. There are ten reservoirs within this series that consist of 99% plexi - totally unique! But the main difference between these reservoirs is within the functionality of the different sockets.
It is placed at the bottom of the reservoir to prevent turbulences that could lead air into the watercircle.
The "Lighttower" effect creates an astounding visual experience within every watercooling system. The Eisbecher supports this in two different ways: fluid coming from the bottom and coming from the top. The water is being led through the standpipe to the bottom or to the top where it splashes out of eight evenly distributed holes at the end of the pipe to the inner wall of the reservoir. This special watergame is the so called "Lighttower" effect.
The known feet from the "Eisdecken" find its very way even to the Eisbecher and sustain every combination with a solid stand.
There are two mountings placed above and under the pipe for fastening the lot in the casing. The holes in this mounting have a spacing of a 120/140 cooling fan.You can reduce the width of the mountings up to the width of the reservoir and there are three M4 threads availaible per mounting for fastening if you would rather not mount the reservoir at the fan space. These mountings are easily removeable especially when not being used. You will find these mountings on all 20 reservoirs.
The lighting modules consist of plexi and enable the lighting with a 5mm LED. These modules can be installed into all 1/4" holes. They are being used in the lid and occasionally in the socket of the reservoir. This facilitates a unique way to your personalised lighting effects.
All models of the reservoir are availaible in acetal and plexi. So there is something for everone.
All reservoirs are availaible in two different sizes: the 150mm version and the 10cm bigger 250mm version. The smaller reservoir comes with only one standpipe coming from the bottom because of its size and the bigger reservoir comes with two: one coming from the top and the other one from the bottom.
The Eisbecher D5
This Eisbecher is the older brother of the DDC version. The pump is being mounted with a mounting ring that holds the pump with eight screws. You can use four LEDs that are hidden within the socke of the pump for the lighting of the plexi version. The lighting of the top is fascilitated through the lighting module. Standpipe and Bubble Down both do an excellent job in this model as well. The fastening happens through either the mountings or through the bases that are included in the delivery. There are even threads in the socket of the pump should there be a free space at the 3,5" drive bay (pump decoupling with M4 inner thread and outer thread needed - Art. 52007).
Included in delivery:
- 4x M4x25mm screw
- 8x M4x8mm screw
- 4x M4 nut
- 1x mounting ring
- 1x O-Ring ID ca. 54mm
- 2x base
- 1x allen key 2,5mm
Measurements 150mm Version:
Measurements incl. mounting without base (LxWxD): 176 x 136 x 79,5mm
Measurements without mounting incl. base (LxWxD): 223,5 x 87,5 x 80mm
Diameter of the Plexitube: 60mm
Attention: The manufacturer Mayhems advises that Mayhems fluids, especially the Aurora line of products, have been manufactured and distributed solely for show and modding purposes. These should not be utilized in the system for more than 14 days.
We would also like to advise that Mayhems fluids can damage water cooling products, and using Mayhems fluids can thereby void the warranties offered by the following manufacturers: Koolance, Phobya, Alphacool, Aqua Computer, Watercool.
Damages such as: clogging, corrosion of aluminium radiators, deterioration of glued containers, etc., are a consequence of the use of Mayhems, but will not be reimbursed by Mayhems. Use is therefore at one’s own risk.
In order to use the intake from the top, a G1/4” extension piece is necessary (article 1011183-1011186), since the screw thread is embedded a few mm into the lid and many compression fittings will not be able to be screwed in.
|LED hole:||niet beschikbaar|
|Type reservoir:||Buis reservoirs - 60mm|
|Compatibiliteit pomp:||voor 1x D5|
Klik hier om deze vraag (en) weer te geven.
Klik hier om deze beoordelingen te bekijken.
Leider sind die zwei Streben die and die Halterungsringe am Becher befestigt sind Maschinell so stark festgeschraubt, das man diese nicht lösen kann ohne das der bei liegende Sechskantschlüssel oder die Schraube ausreißt.
Desweiteren ist die Anleitung entweder überholt oder unzureichend, die dort angegeben Schrauben stimmen nicht mit dem Lieferumfang überein und der ORing wird erst gar nicht erwähnt.
Werde den Becher wohl zurückschicken, da ich ihn so nicht wie gewollt an meinem Radiator befestigen kann.
Läuft bei mir seit Februar ohne Probleme , es gibt sehr viele möglichkeiten ihn zu befestigen und ebensoviele Anscvhlussmöglichkeiten. Inbetriebnahme und entlüftung liefen ohne Probleme. Kann ihn bedenkenlos weiter empfehlen.